Wednesday, 6 July 2011

Visit to Lode Mill, Anglesey Abbey

Today we visited Lode Mill, part of the National Trust's Anglesey Abbey estate. This is another big, multi-storey mill, again mainly built of wood but with a large, iron 4 o'clock breastshot wheel.


The mill wheel


The stone floor



Once again we found the person in charge, in this case Chris Stimson, was generous with his time and knowledge and showed us round the mill and millwheel, including parts not normally open to the public.

He agreed with the thought that it was illogical to mill flour NOT for consumption. We would, however, have to sort out the lifting of delivered grain to the upper floor.

There was a suggestion that if you mill on four days or fewer in any five week period, there may be exemptions from some of the food hygiene regulations - but this may conflict with tea room use, of course.

Lode Mill also offers a hand quern and the opportunity to handle grain and flour - in general both mills had excellent educational facilities and interpretation.


Un-greased wooden cogs
Chris stated that you should NOT grease wooden cogs, as they pick up dust and debris to form an abrasive mixture that wears the wood too rapidly. maybe a better option for us would be to smooth the surface of the stone nuts.

Lining of grain boxes can be achieved with sheet aluminium as a Houghton, or metal gauze as at Lode. Other containers are mainly plastic Really Useful Boxes, one with a hole cut for the flour chute - on a table, not at floor level.

There are some issues around cleaning up after every milling, stone speed and tentering all of which we need to resolve - the input of a miller was stated to be essential, so Nic Jones' input needs to be obtained.

Tuesday, 5 July 2011

Visit to Houghton Mill near Huntingdon


Today we (Bob and Glenis) visited the National Trust's watermill at Houghton. We were made extremely welcome by Phil O'Donohue and Steve (sorry, can't remember his surname), who spent two full hours showing us round and discussing some of the issues around milling.

Houghton Mill is a rather bigger affair than Acorn Bank, being on 5 floors and powered by a "4 o'clock breastshot" wheel about 15 feet in diameter and 16 feet wide. They produce flour in one operating session each Sunday afternoon, which is sold at the mill and makes a valuable addition to the economics of the property.

The main lesson was that if we are milling flour, we ought to sell it, otherwise the public will (rightly) ask why we are bothering. They suggested that we should get the local authority food hygiene people involved as soon as possible. Their flour is also used in their tearoom scones, and it was suggested we should consider doing the same.

They also have a hand and a rotary quern to show the concept of milling - I think we should have at least one of these.

The design of our tun needs some extra consideration, as the uprights will form pockets in which flour can become trapped. This photo shows the Houghton solution of fixing internal boards across the angles.

They always un-tenter the stones after each milling session, as the flour can pack down into a dense, cement-like substance if left under pressure.

Tuesday, 28 June 2011

Further work on No 2 stone

Today we continued to work towards our goal of milling with the No 2 stone before the end of the season.

The tun is a two-decker structure, the upper section being detachable mainly to make it easier to get it in and out of the limited space.
Ray made good progress with the tun, putting in the cross bracing timbers which will support the top and help it to support the horse ...
... and built the top, made like the rest of the tun from tongue and groove floorboarding. All that remains is to finish trimming the edges of the top, cut the central hole for the grain to enter, finish the internal reinforcing, and finish and stain the wood.


Bob and Richard worked on the stone nut disengaging mechanism. The vertical bars have had to be modified as the holes in the tentering beam through which they pass are no longer vertical. To give a little flexibility, the bars are no longer fixed into holes in their bottom plate - instead they have collars which rest on the plate. Today's task was to fix the collars by drilling and fitting spring pins, and then refit the bars.

Finally we made a second hole in the cement dressing on the top of the runner stone and filled it with molten lead to balance the stone.

Monday, 27 June 2011

Repair to the Dump Valve

As previous blogs will relate (once I get round to entering them - I am blogging most of this stuff retrospectively), we have a sort of "emergency stop" lever for the mill. It works by dropping a board out of the bottom of the launder close to the wheel, stopping the flow of water much more quickly than closing the diverter. We call this the Dump Valve.

During Sunday 19th June's operation, we found that the dump valve was not closing properly, spilling a lot of water. It then failed to open properly and stop the wheel at the end of the afternoon.

Investigation showed that there was a lot of algae and other green slimy stuff in the works, but once this was removed it became apparent that the arm that works the valve flap was not fixed securely to the operating shaft. In fact the coach screws were in soft, wet timber and could not be tightened.



The Dump Valve operating arm,
showing the rigid link

We therefore bored out the holes in both the arm and the shaft to take 12mm studding, made and drilled 2 plates from 3mm mild steel, and reattached the arm. We also removed a bit of the timber cladding where the operating lever comes through the end of the wheelhouse to allow the lever to move further.

After we had adjusted the operating chain, the valve worked perfectly until the drop board jammed in the hole.

12 July 2011 fitted a rigid arm so the lever now pushes the drop board open rather than allowing it to fall under its own weight..

Tuesday, 14 September 2010

Restoration of No 1 stone

Acorn Bank watermill has 4 pairs of stones. Nos 1 and 2 are respectively an oat shelling stone and a French burr, driven by the upstream waterwheel. The downstream waterwheel is incomplete, so any work on stones 3 and 4 will be part of a much larger project.

We decided to begin by restoring stone no 1 to rotation, with no intention of shelling any oats, simply because it looked easiest! This is a diary of the restoration, interrupted several times by the need to repair other parts.



No 1 stone before restoration

09/06/2009 Fitted supporting beams and used hoist to lift no 1 shelling stone. Stone wedged back against wall.



The bed stone and rynd...



...and the runner (photos courtesy Martin Watts)

15/06/2009 Dismantled bearing in no 1 bedstone. Bearing in good condition; to be recorded before reassembly. Checked engagement of stone nuts - they will not lower far enough to engage spur wheel.

11/08/2009 Checked alignment of no 1 stone driveshaft

18/08/2009 Removed stone driveshaft and stone nut. Adjusted position of drive taper (25mm down). Left machine secure for weekend

25/08/2009 Removed tentering beam and treated with timber preservative, cleaned and painted shaft. Removed beam socket box and painted with primer. Refixed in wall socket.

01/09/2009 Reassemble tentering beam. Make lead bearing cover for same. Measure stone separation etc to ensure proper engagement of stone nuts with spur wheel. Removed part of tun base and floor boards to investigate possibility of moving bedstone to correct gear meshing.

08/09/2009 Cutting beams and floorboards so bedstone can be moved. Clean stone drive shaft.

15/09/2009 Levelling floor round no 1 stone and removing tun base

06/10/2009 Moved no 1 bedstone 10mm further from main shaft and levelled.

13/10/2009 Replaced stone drive shaft. Stone nut assembled to shaft in pit and whole assembly hoisted in several stages by rope through bedstone bearing. Bottom bearing and bearing block added afterwards. Bearing rebuilt by inserting sacking impregnated with oil, and re-attaching the 3 wooden bearing surfaces. Rynd attached. Stone nut lifting fork reattached - some difficulty separating stone from taper. Wheel run to check assembly - good! Stone nut tried in different orientations, but still does not run level.

23/03/2010 Fit wooden octagonal bezel to no 1 bedstone.

14/09/2010 Refitted no 1 stone. Packing pieces made from sheet lead, thinned at edges so they could be hammered in. Rynd tried in position and depths measured to estimate thickness of shims required. Stone approximately levelled - running true to drive shaft, but could have moved bed stone a few mm further out as shaft is at slight angle, so stone higher at upstream side. This is corrected over next few weeks by repeated small adjustments of bottom bearing as gear teeth wear in. Whole machine runs quieter with stone turning.

The first time a stone has turned for at least 60 years!

Tuesday, 10 August 2010

Preparing to restore the French Burr stones

The second pair of stones in the mill are French Burrs, which were used to mill wheat flour. Like the first pair, these stones have not operated since WWII.

Naturally, we would like to restore these stones to working order with the intention of milling some flour in due course.

There are several problems - we have no idea what state the stone faces or bearings are in, the support beam is twisted, the stone nut is mounted too high on the shaft to mesh with the spur wheel, and it is also too close to the spur wheel so the gears cannot engage. Apart from that and the fact they are enormously heavy (over a ton each), it looks quite simple. Oh, and there is no beam in the roof in a suitable position to attach a lifting block.

So, the first step is to fit a lifting beam. After lots of calculations to work out how big a beam we needed to span the 3m gap between roof timbers above stones 2 and 3, we eventually ordered a length of oak, 3.5m long and 20cm square. On August 10th this 150kg monster was dragged across the yard on rollers and then pulled in through the half-door by a hoist attached to existing timbers. By using hoists in various positions, and extra manpower provided by Chris Braithwaite, we eventually got it lifted into place.


The lifting beam in position with 3 ton chain block

07/09/2010 We fitted blocks to the ends of the beam to stop it slipping out. During the hammering a bat fell out of the roof. Following instructions, we picked it up (wearing gloves) and stuck it on the wall, from where it flew back to safety.

Tuesday, 22 June 2010

Repairing the Sluice

13/04/2010 Sluice gate has collapsed under water pressure due to rot.


The new sluice gate

At first we inserted plywood boards to reduce water flow.
Removed side posts (grooved for sluice gate boards), which were cemented into channels cut in stonework. Make new boards and design and manufacture new sluice valve with steel blade and slides and screw control. Install new sluice mechanism. Replace rotting bridging boards with more stable arrangement.

01/06/2010 Make new weir handrail from scaffolding sections.

08/06/2010 Weir handrail fitted
- adjusting the sluice was previously a hazardous activity.
15/06/2010 Finishing fixing of weir handrail.

22/06/2010 Further work on weir handrail.

28/09/2010 Wheel control added.